Difference between revisions of "Testing of PMT dividers"

From GlueXWiki
Jump to: navigation, search
 
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
''' New version of the active base'''
 +
<gallery>
 +
Image:new_base2.jpg  |  Fig. 1  Connectors on the new base
 +
Image:new_base3.jpg  |  Fig. 2  Connectors on the new base
 +
Image:new_base1.jpg  |  Fig. 3  Extension of the PCB to accommodate the new connector
 +
</gallery>
 +
 +
'''[[Final test of dividers]]'''
 +
 +
 
''' Bench tests'''
 
''' Bench tests'''
  
Line 28: Line 38:
  
 
<gallery>
 
<gallery>
−
Image:ccal_prot_cables1.jpg  |  Fig. 1 - Front view of the CCAL
+
Image:ccal_prot_cables1.jpg  |  Fig. 1 - Cables connected to the FCAL2 dividers (signal, HV, and LV)
−
Image:ccal_prot_cables2.jpg  |  Fig. 2 - Rear view of the CCAL
+
Image:ccal_prot_cables3.jpg  |  Fig. 2 - Cables connected to the FCAL2 dividers (signal, HV, and LV)
−
Image:ccal_prot_cables3.jpg  |  Fig. 3 - List of modules installe
+
Image:ccal_prot_cables2.jpg  |  Fig. 3 - Closer look of dividers
−
Image:ccal_prot_cables4.jpg  |  Fig. 3 - List of modules installe
+
Image:ccal_prot_cables4.jpg  |  Fig. 4 - Patch panels: LV distribution for the 5x5 prototype (right) 
−
Image:ccal_prot_cables5.jpg  |  Fig. 3 - List of modules installe
+
Image:ccal_prot_cables5.jpg  |  Fig. 5 - Patch panel from the outside of the CCAL (the MPOD connector is on the left)
 +
</gallery>
 +
 
 +
 
 +
'''Tuning dividers after the CCAL beam test '''
 +
<gallery>
 +
Image:before_saturation_fern.png | Fig. 1 Original base before saturation
 +
Image:after_saturation_fern.png | Fig. 2 Original base, A = 1.8 V
 +
Image:new_ops.png | Fig. 3 Modified OPS
 
</gallery>
 
</gallery>

Latest revision as of 09:43, 19 October 2023

New version of the active base

  • Fig. 1 Connectors on the new base

  • Fig. 2 Connectors on the new base

  • Fig. 3 Extension of the PCB to accommodate the new connector

Final test of dividers


Bench tests

  • Fig. 1 Setup for testing PMT dividers

  • Fig. 2 Bypassed amplifier, small amplitude

  • Fig. 3 Bypassed amplifier, large amplitude

  • Fig. 3 Amplifier gain 3, small amplitude


Study noise inside FCAL



Installing 5x5 prototype on CCAL

  • Fig. 1 - Front view of the CCAL

  • Fig. 2 - Rear view of the CCAL

  • Fig. 3 - List of modules installe


Cables, and patch panels

  • Fig. 1 - Cables connected to the FCAL2 dividers (signal, HV, and LV)

  • Fig. 2 - Cables connected to the FCAL2 dividers (signal, HV, and LV)

  • Fig. 3 - Closer look of dividers

  • Fig. 4 - Patch panels: LV distribution for the 5x5 prototype (right)

  • Fig. 5 - Patch panel from the outside of the CCAL (the MPOD connector is on the left)


Tuning dividers after the CCAL beam test

  • Fig. 1 Original base before saturation

  • Fig. 2 Original base, A = 1.8 V

  • Fig. 3 Modified OPS

Retrieved from "https://halldweb1.jlab.org/wiki/index.php?title=Testing_of_PMT_dividers&oldid=123259"