Difference between revisions of "GlueX phase 2, 2023-01 data set"
From GlueXWiki
(→Periods) |
(→Periods) |
||
Line 31: | Line 31: | ||
* period 18: 120693-120709 (PARA/PERP AM0) | * period 18: 120693-120709 (PARA/PERP AM0) | ||
* period 19: 120710-120733 (PARA/PERP AMO) | * period 19: 120710-120733 (PARA/PERP AMO) | ||
− | * period 20: 120734- | + | * period 20: 120734-120790 (PARA/PERP AMO) |
+ | * period 21: 120???-120??? (PARAP/PERP AMO) | ||
== Timing == | == Timing == |
Revision as of 15:41, 21 February 2023
Contents
List of changes
These lists are giving the run ranges where the FCAL hardware was not changed.
Monitoring results
What is currently in the default variation
Periods
The periods in BOLD are calibrated i.e. have a pedestal and gain tables. Each period corresponds to constant FCAL and/or experimental conditions.
- period 0: 120166-120222 (AMO, commissioning)
- period 1: 120223-120266 (AMO mostly HV scans for TAGH/M, few cosmics, commissioning)
- period 2: 120267-120268 (AMO & Empty Target, commissioning)
- period 3: 120269-120285 (AMO, commissioning)
- period 4: 120286-120311 (AMO not clear if Empty or Full)
- period 5: 120312-120316 (PERP/PARA not clear if Empty or Full)
- period 6: 120317-120318 (AMO not clear if Empty or Full)
- period 7: 120319-120330 (PERP/PARA - AMO-120327 not clear if Empty or Full)
- period 8: 120331-120373 (PERP/PARA - AMO-12036[2-4] Full)
- period 9: 120386-120421 (PERP/PARA - AMO-120392-120403-120415 Full)
- period 10: 120436-120479 (PERP/PARA - AMO-120442-120443-120444-120450-120457-120458-120469 Full)
- period 11: 120480 (AMO - junk?)
- period 12: 120481-120487 (PERP)
- period 13: 120488-120521 (AMO - high-intensity test)
- period 14: 120522-120547 (PARA/PERP AMO-120545-120546-120547)
- period 15: 120548-120568 (PARA/PERP)
- period 16: 120569-120609 (PARA/PERP AMO)
- period 17: 120610-120692 (PARA/PERP AMO)
- period 18: 120693-120709 (PARA/PERP AM0)
- period 19: 120710-120733 (PARA/PERP AMO)
- period 20: 120734-120790 (PARA/PERP AMO)
- period 21: 120???-120??? (PARAP/PERP AMO)
Timing
Pedestals
The pedestal calibration is performed for each run.
- period 0: 120166-120222 (AMO)
- period 8: 120331-120373 (PERP/PARA - AMO-12036[2-4] Full)
Gain matching calibration plots
Checking the FCAL gains
Energy dependence correction monitoring plots
Timing calibration
Is based on
- period 8: 120331-120373 (PERP/PARA - AMO-12036[2-4] Full)
but applied to all 2023-01 data set
Bad block map
This map is done for each run number by combining the info collected by analyzing the LED and pi0 skims.
- period 0: 120166-120222 (AMO)