Latest revision as of 09:00, 7 October 2024

Connection

Meeting time and location:

• 9:30 am EST (JLab time) remote only
• Connection information

Agenda

Preparation of parts for ECAL -- Sasha

• - long HV cables - done
• - HV distribution boards [1][2]

- 5 (12 x 4) and 5 (6 x 8) boards have been received. Received all PCB boards. Soldering wires to connectors (one distribution board is ready, one more board will be ready during next week)

- Sent out request of quotes for HV board boxes

- Consider to build temporarry boxes for testing

• - Two panels for the LV distribution boards received, need to re-connect cables (Sasha, Laveen, Vlad) [3]

Installation of the FCAL2 detector & integration to GlueX -- Sasha, All

• Installation of the light distribution board of the ECAL LMS [4]

- Fine-tune the light source

• Implementing ECAL into the GlueX DAQ [5]

- rocecal3 crate was fixed [6] (initial DAQ implementation [7])

- implementing flash ADC scalers [8]

- translation table for the ECAL (finalize/check translation DB, generate xml file, import to the CCDB) - done [9]

- implementing and verifying ECAL LMS trigger [10]

- implementing and verifying the ECAL physics trigger. First event reconstructed using the GlueX software [11]

- Installation of scintillating paddles for cosmic tests [12]

• Detector installation page
• Safety briefings
• Meeting with Drew Weisenberger regarding Vlad'd involvement in commissioning
• FCAL2 Engineering Meetings
• Remaining installation tasks

- Connecting cooling pipes to the ECAL fan (done by tech group)

- Installing dark room ceiling and insulation inside the room, required for cooling test (next week)

- Test cooling system (next week)

- Installing HV distribution boards, start switching the detector ON (waiting for HV boxes)

Students -- Sasha

• Zhikun arrived to the lab

Restoring PS test setup [13]

ECAL commissioning -- Sasha, All

Minutes

Attendees: Bill, Sasha, Igal, Vlad, Laveen, Zisis, Ilya, Stjepan, S.T.

• Student from Wuhan has arrived
• HV pcbs arrived, connectors being soldered onto boards, one set ready to go
• Still missing boxes to house these pcbs, plan to build temporary solution
• Position of LV distribution panels lowered, need to be re-cabled
• Need to increase light intensity for LMS
  • Prototype light input using 5 LEDs leeds to small amplitudes (~100 mV)
  • Would like to increase light intensity 10x
    • Many possible solutions considered: tune pulse width? increase number of LEDs? get rid of integrating sphere?
• DAQ commissioning continues
  • Translation table for ECAL done, still working on translation table for lead glass
  • ECAL low-level scalers from DAQ system working, EPICS scalers still need work
  • Can read out digihits for ECAL (read out all 7 ECAL crates) -- flashADC waveforms seen!
  • Front panel LMS trigger working, progress on ECAL physics trigger (working, energy sum from signal pulses induced by the LMS)
    • However: barely enough CTP (Crate Trigger Processor) modules (no spares)
    • Plan to use new type of board for trigger: VXS Trigger Processor (VTP)
      • Have 8 VTPs to replace CTPs, installed one
      • VTPs need new firmware -- one month needed?
• Cosmic ray setup: installed scintillator paddle below FCAL, will install one above FCAL
• Cooling system installation/testing and dark room ceiling proceeding
• ECAL commissioning page under development
• Laveen continues working on close-shower separation studies -- FCAL-2 geometry -> Ilya's code
• Physics discussion:
  • Exclusion plots need to be updated (plots from proposal don't reflect our current understanding of the backgrounds)
  • Degree of background suppression needs to be presented carefully in future talks
  • Need to come up with data analysis strategy
  • Make a list of physics channels ranked from "easy" to hard